Mon - Fri 08:00-18:00

BMW E87 1 Series 120D 174 BHP EDC17CP02 2007 to 2009

230 BHP

Stage 1 Power

440 Nm

Stage 1 Torque

BMW E87 120D 174 BHP EDC17CP02 Stage 1 Remap

The BMW E87 120D available from 2007 to 2009 is equipped with the Bosch EDC17CP02 ECU. The 120D is very receptive to a Stage 1 remap and will deliver great results without needing any hardware upgrades.

This stage 1 remap elevates the performance from 174 BHP to an impressive 230 BHP and we enhance the torque from 350Nm in its original state to a robust 440Nm. The torque delivery is designed to be both smooth and progressive, ensuring compatibility with your clutch or automatic transmission while providing a thrilling driving experience.

After fitting your vehicle with an HDI Tuning Remap, you’ll immediately notice why our service is highly regarded. We not only boost your torque and power substantially, but we also prioritise engine safety and we focus on smooth torque delivery. Our remap is meticulously tailored, with the torque curve engineered to align with the engine’s air mass and inherent characteristics.

While HDI Tuning is recognized as an HDI expert, our expertise in engine tuning especially in BMW EDC17 tuning is unparalleled, outmatching 99% of tuning companies in the industry. Our remap for the BMW EDC17 is truly a step above the rest.

You have the option to program the Bosch EDC17CP02 ECU on your own using our MyGenius tool. This tool enables direct programming through the OBD port, eliminating the need to disassemble the ECU. With MyGenius you can switch between remaps at your convenience and access multiple maps with varying power levels. If that’s something that would interest you then please get in touch to discuss which remaps you’d like.

Price:

Programming Methods – OBD2 or KTAG

Programming via OBD EDC17

  • Obtain a suitable programming tool; we recommend to use Dimsport MyGenius.
  • Connect to the OBD port of your car, make sure you have battery support to the vehicle battery.
  • ID the ECU and then take a read of the ECUs flash memory.
  • Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
  • Send payment through our webshop.
  • We will modify the software and send back to you. This normally takes less than 2 to 3 hours during working days.
  • Using the same tool you can then write to the ECU. This will overwrite the ECUs flash memory, it’s important not to interrupt the process.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!

Bench Programming via KTAG EDC17

  • Order a suitable tool such as KTAG
  • Install the tool to a reliable laptop.
  • The ECU must be removed from the vehicle, and then the ECU needs to be opened, don’t attempt this unless you know what you are doing otherwise you can damage the ECU.
  • Connect boot pin to processor and CAN hi Lo / +12v / GND to pins on ECU
  • ID the ECU and then take a read of the ECUs memories for a backup (please save separately, and not as a combined file).
  • Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
  • Send payment through our webshop.
  • We will modify the software and send back to you. This normally takes less than 2 to 3 hours during work days.
  • Using the same tool, ID then write to the ECU. This will overwrite the ECUs memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about (You can always repair an ECU if you take a full backup of all memories).
  • Straighten the lid on the ECU and seal with a little silicone.
  • Refit the ECU and start the engine.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!