Mon - Fri 08:00-18:00

1.6 HDI 8V 75 DPF 2010 – 2015 Bosch EDC17C10 EU5 Rifter

120 BHP

Stage 1 Power

290 Nm

Stage 1 Torque

Stage 1 – DPF Safe (120 BHP | 290 Nm)

Our Stage 1 remap will take your 1.6 75 BHP engine straight up to 120BHP and 290Nm. The components fitted to the 75 variants are 100% identical to the 90 engine, only the software is down-tuned. This gives you a massive power gain whilst remaining completely safe.

Our stage 1 remap provides constant smooth torque through the entire rev range whilst remaining well within the safe limits of your clutch and turbo charger.

The DPF system will not be affected by this remap as we remain well within stock air fuel ratios to promote a clean sootless burn.

Although this remap is an extremely safe remap, you will still be pleasantly surprised at just how much extra torque and useable power is available after the remap. As we specialise in tuning only HDI engines we are able to offer much more advanced remaps than our competitors without hitting any kind of tuning protection limits from the complex EDC17 software.


Stage 1 + Remap (125 BHP | 300 Nm)

The Stage 1 + remap is designed for those who want that little bit extra and also have a performance exhaust fitted. Peak power with this remap is 125 BHP and peak torque comes out at 300Nm making a big difference to the way your car drives.

For best results, run a straight through exhaust system with a straight through back box. You can also upgrade to a high flow air filter. Avoid using oiled filters as these can degrade the MAF element and cone filters usually suck more hot air from the engine bay.


Stage 2 (130 BHP | 310 Nm)

The stage 2 remap requires an upgraded intercooler and also an upgraded exhaust system. The intercooler should be as large as you can fit behind the bumper, this makes a big difference on the 1.6 8v engine as we found the intercooler to suffer from heat soak when run consistently hard or on a dyno. The exhaust can be 2.5 inch all the way through with a free flowing type silencer.

With the uprated intercooler and exhaust system we can take you up to 130 BHP and 310Nm. This remap can be ran with the DPF intact, we did extensive testing with this much heavier remap and found the DPF stayed perfectly clean (this assumes you will do regular long journeys to allow the vehicle to get up to temperature).


Stage 3 – Turbo upgrade (150 BHP | 320 Nm)

We’ve spent a lot of time working on a VNT turbo upgrade. The turbo used here is a GTD1244VZ from the 1.6 Blue HDI 120 model which is almost a direct fit. This gave great performance figures with 320Nm torque and 150 BHP. Here you will notice that the power does not drop off at higher engine speeds, it will continue all the way past 4500 RPM.

To get optimum performance you need to fit an uprated front mount intercooler and also and free flowing exhaust system of 2.5”.

There is no need to upgrade the injectors or any other parts. A full fitment guide is available here.

You cannot run this turbo upgrade without a remap as the ECU will detect that the turbo position sensor is different, as such it will keep the car locked in to limp mode. This is important as going from a waste-gated turbo to a VNT turbo requires the turbo control software to be modified so that the ECU can safely regulate the boost of the VNT turbo. It’s best to fit the turbo once you have the software ready to program to the ECU.


Which vehicles are covered?

The power figures quoted on this page are applicable to the following vehicle models if fitted with a Bosch EDC17C10 ECU and the 1.6 8v Euro 5 HDI engine:

Peugeot Partner 1.6 8v 75 BHP
Peugeot Expert 1.6 HDI 8v 75 BHP vans
Citroen Berlingo 1.6 8v 75 BHP van
Citroen Dispatch and Citroen Jumpy 1.6 8v 75 BHP vans

If your vehicle is not listed directly but you have the 1.6 75 variant 8v engine with the TD02 turbo you can assume these figures will be correct.

Programming Methods – OBD2 or bench programming

We recommend to use only genuine tuning tools to program the EDC17C10 over OBD. Dimsport MyGenius is able to do this over OBD by taking a virtual read and then offers full programming capabilities with the option to change maps whenever you choose. We have also tested the use of Kess with a virtual read and this can also successfully write the ECU over OBD. Always add battery support to the vehicle to prevent a voltage drop during programming.

Recommended programming method:

Program over OBD using the Dimsport MyGenius standalone tool


The Dimsport MyGenius tool is the safest, easiest and most reliable way to program your ECU from home. Simply connect to the OBD port and let the tool do the work, no need to remove your ECU or bench program for most ECU types. For more information have a read here

Programming via OBD EDC17C10

  • Obtain a suitable programming tool. We recommend Dimsport MyGenius if you want to program over OBD.
  • Install the tool to a reliable laptop.
  • Connect to the OBD port of your car, make sure you have backup chargers to the vehicle battery and the laptop battery.
  • ID the ECU and then take a read of the ECUs flash memory.
  • Email the software to along with a description of the remap you require.
  • Send payment through our webshop.
  • We will modify the software and send back to you. This normally takes less than 2 to 3 hours during working days.
  • Using the same tool, ID then write to the ECU. This will overwrite the ECUs flash memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!

Programming via Bench service mode KTM Bench or PCM Flash

This is our preferred way to program. The ECU must be removed, but there is no need to open the ECU and risk damage. A full backup can be made of both the EEPROM and the internal flash memories, also the external flash can be read on models where this is present.

  • Order a tool such as KTM bench or PCM Flash.
  • Remove ECU from the vehicle.
  • Connect specified wires to ECU plug connector.
  • ID the ECU.
  • Read the ECU memories.
  • Email software to HDI Tuning.
  • Wait for us to prepare your remap and return it back to you.
  • Program the remap to the ECU using the same method taken to read the ECU.
  • Refit the ECU, check engine starts.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!