If you’re looking into a remap for your Peugeot Expert 1.6 BlueHDI, then you’re in the prime spot. At HDI Tuning, we offer a range of remaps fine-tuned explicitly for this engine and its complex ECU model (Bosch EDC17C60). Our specialists have poured hours into rigorous research and calibrations and tuning work to devise this elite remap. With HDI Tuning, it’s not solely about bumping up power; our hallmark is steadfast reliability.
If you’re inclined to program the ECU yourself, the MyGenius OBD programmer is at your available in our webshop. This apparatus links through the OBD diagnostic connector, bypassing the need to remove and dismantle the ECU. While special tools aren’t a mandate, it’s important to have a battery charger or stabilizer at the ready during the ECU writing phase, this keeps ECU voltage steady.
Peugeot Expert 1.6 BlueHDI 75 – Stage 1 (126 BHP
| 300 Nm
)
Our Stage 1 remap for the Peugeot Expert 1.6 BlueHDI 75 BHP harnesses 300Nm of torque with maximum power of 126BHP. This stage 1 enhancement promises even torque distribution throughout the rev spectrum, ensuring the vehicle moves with finesse, making it great fun to drive.
During ECU modifications, our commitment is to mirror the OEM torque architecture, retaining the integrity of the torque monitoring structure and following the same approach that PSA do when producing a more powerful version. This equates to reliable power delivery without imposing any strain on the DPF.
Price:
- Program yourself with the MyGenius OBD tool, includes a Stage 1 Remap for just £290!
- Already have a programming tool? Use our Online remap service for just £150
- Send us your ECU – Use our Postal Remap Service £200
Stage 3 (150 BHP
| 320 Nm
)
Our Stage 3 remap requires a turbo upgrade and will take your 75 BHP BlueHDI to 150BHP and a staggering 320Nm of torque. The stage 3 performance remap provides consistent smooth torque through the entire rev range and great top end power. The 120 BHP BlueHDI engine is fitted with an excellent fourth generation Garrett GTD1244VZ turbo from the factory, we simply need to fit this turbo and then the software is changed to take account of this. There is no need to change the injectors as these are the same on all 1.6 BlueHDI engines.
Stage 3 (185 BHP
)
The Stage 3 remap uses a hybrid GTD12 turbo. The turbo needs an upgraded 49mm compressor wheel fitted and the compressor housing machined to match. The turbine side is unchanged, the thrust bearing should be upgraded to a 360 bearing to add strength.
This remap also requires an upgraded intercooler, ceramic paddle clutch (there is a LOT of torque) and a full 2.5 inch exhaust system.
Price:
- Please enquire via email for a customised quote.
Which vehicles are covered?
The power figures quoted on this page are applicable to the following vehicle models if fitted with a Bosch EDC17C60 ECU and the 1.6 Euro 6 BlueHDI engine:
Peugeot Partner 1.6 8v 75 BHP BlueHDI
Peugeot Expert 1.6 HDI 8v 75 BHP vans BlueHDI
Citroen Berlingo 1.6 8v 75 BHP van BlueHDI
Citroen Dispatch and Citroen Jumpy 1.6 8v 75 BHP vans BlueHDI
If your vehicle is not listed directly but you have the 1.6 75 BlueHDI 8v engine with the TD02 turbo charger and AdBlue fitted, you can assume these figures will be correct.
Programming Methods – OBD2 or bench programming
Only genuine tuning tools can program the EDC17C60 over OBD such as Autotuner, Combiloader, and now we can also program this ECU type using Dimsport MyGenius.
Recommended programming method:
Program over OBD using the Dimsport MyGenius standalone tool
The Dimsport MyGenius tool is the safest, easiest and most reliable way to program your ECU from home. Simply connect to the OBD port and let the tool do the work, no need to remove your ECU or bench program for most ECU types. For more information have a read here
Programming via Bench service mode PCM Flash or any tools with bench service mode
This is our preferred way to program. The ECU must be removed, but there is no need to open the ECU and risk damage. A full backup can be made of both the EEPROM and the internal flash memories, also the external flash can be read on models where this is present.
- Order a tool such as KTM bench or PCM Flash.
- Remove ECU from the vehicle.
- Connect specified wires to ECU plug connector.
- ID the ECU.
- Read the ECU memories.
- Email software to HDI Tuning.
- Wait for us to prepare your remap and return it back to you.
- Program the remap to the ECU using the same method taken to read the ECU.
- Refit the ECU, check engine starts.
- Let your engine warm up and then take the car for a spin, enjoy the extra power!
Bench Programming via KTAG
- Order a suitable tool such as Kess KTAG
- Install the tool to a reliable laptop.
- The ECU must be removed from the vehicle, and then the lid can be carefully pried open and removed. The best way to do this is with 1 small flat head screw driver, 1 medium, and one large. A heat gun will help soften the sealant. Always start at the end furthest from the flat bonded section of the lid. If you attempt to pry open this end you will damage the ECU. A video guide is available on youtube.
- Connect necessary pins to ECU connector plug.
- Connect boot pin to correct location. The processor is a TC1793.
- ID the ECU.
- Take a read of all memories present.
- Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
- Send payment through our webshop.
- We will modify the software and send back to you. This normally takes less than 2 to 3 hours during work days.
- Using the same tool, ID then write to the ECU. This will overwrite the ECUs memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about, if you made a backup of all memories you’re extra safe in the event that something were to go wrong.
- Straighten the lid on the ECU and seal with a little silicone.
- Refit the ECU and start the engine.
- Let your engine warm up and then take the car for a spin, enjoy the extra power!
Programming via OBD EDC17C60
- Obtain a suitable programming tool. We recommend Dimsport MyGenius if you want to program over OBD.
- Install the tool to a reliable laptop.
- Connect to the OBD port of your car, make sure you have backup chargers to the vehicle battery and the laptop battery.
- ID the ECU and then take a read of the ECUs flash memory.
- Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
- Send payment through our webshop.
- We will modify the software and send back to you. This normally takes less than 2 to 3 hours during working days.
- Using the same tool, ID then write to the ECU. This will overwrite the ECUs flash memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about.
- Let your engine warm up and then take the car for a spin, enjoy the extra power!