Mon - Fri 08:00-18:00
remap@hdi-tuning.co.uk   

BMW 530D 218 BHP EDC16C31

270 BHP

Stage 1 Power

600 Nm

Stage 1 Torque

Banner

BMW E60/61 530D 218 BHP EDC16C31 Stage 1 Remap DPF safe remap

Our Stage 1 power remap for the 530D was created, developed and tested in house to the highest of standards. You simply won’t get a remap that behaves as smoothly as refined as ours elsewhere. To top it off, our advanced tuning software is priced very affordably.

Not only is our remap incredibly smooth and progressive, the torque is strong and addictive and keeps going to the higher engine speeds. The 530D is nothing short of incredible when running a stage 1 remap. We’re confident that you’ll love the way your car drives after our stage 1 update.

The stage 1 remap gives 270 BHP and a torque increase to 600Nm. Most drivers even gain a few mpg on fuel economy which is very welcomed for this sometimes thirsty 3.0 engine. The HDI Tuning remap completely transform your 530D.

BMW 530D Stage 1+ Remap with sports exhaust

If you’re looking for some extra performance, you can opt for our full power Stage 1 + remap. This will take you to 600 Nm and 280 BHP.
You can program the Bosch EDC16 ECU yourself easily using our online remapping service. For this we recommend to use the Kess V2 tool. With this tool you can you program directly over the OBD port. If you prefer to send the ECU to us for the programming work, you can use our postal remap service.

Price:

Programming Methods – OBD2 or KTAG

Programming via OBD EDC16C35

  • Obtain a suitable programming tool; we recommend to use Dimsport MyGenius, you can also use Kess V2.
  • Install the tool to a reliable laptop.
  • Connect to the OBD port of your car, make sure you have backup chargers to the vehicle battery and the laptop battery.
  • ID the ECU and then take a read of the ECUs flash memory.
  • Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
  • Send payment through our webshop.
  • We will modify the software and send back to you. This normally takes less than 2 to 3 hours during working days.
  • Using the same tool, ID then write to the ECU. This will overwrite the ECUs flash memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!

Programming via KTAG EDC16C35

  • Order a suitable tool such as Kess KTAG or BDM100.
  • Install the tool to a reliable laptop.
  • The ECU must be removed from the vehicle, and then the tabs on the lid can be carefully pried open and the casing of the ECU removed.
  • Using a pogo spring probe connect to the ECU board, power the ECU to the ECU connector plugs as described by your programming tool.
  • ID the ECU and then take a read of the ECUs memories for a backup (please save separately, and not as a combined file).
  • Email the software to remap@hdi-tuning.co.uk along with a description of the remap you require.
  • Send payment through our webshop.
  • We will modify the software and send back to you. This normally takes less than 2 to 3 hours during work days.
  • Using the same tool, ID then write to the ECU. This will overwrite the ECUs memory, it’s important not to interrupt the process. If you encounter any problems we can fix the ECU for you so there’s absolutely nothing to worry about (You can always repair an ECU if you take a full BDM backup of all memories).
  • Straighten the lid on the ECU and seal with a little silicone.
  • Refit the ECU and start the engine.
  • Let your engine warm up and then take the car for a spin, enjoy the extra power!